Paradyne IP Broadband Loop Carrier 4000E Manual de usuario

IPD4-A2-GZ40-10 July 2005 14000E IP Broadband Loop CarrierInstallation InstructionsDocument Number IPD4-A2-GZ40-10July 2005 ContentsSoftware and Firmw

10 July 2005 IPD4-A2-GZ40-104. Select a terminal block. Using a Phillips Screwdriver, remove the upper screw from the chosen terminal block (labeled &

IPD4-A2-GZ40-10 July 2005 115. Remove the right-hand screw (labeled "–") from the same terminal block. Slide the ring terminal of your NEGAT

12 July 2005 IPD4-A2-GZ40-10Uplink ConnectionsNo configuration is necessary for Uplink Interface Modules (UIMs) or Media Interface Modules (MIMs) inst

IPD4-A2-GZ40-10 July 2005 13the A connectors provide the subcriber connections for ports 1-12 and the B connectors provide the subscriber connections

14 July 2005 IPD4-A2-GZ40-104. Pull the hook-and-loop fastener strap upward, making sure that it is snug against the connector, then pull the strap ba

IPD4-A2-GZ40-10 July 2005 15Securing the Connecting CablesPosition all connecting cables such that they will not become a tripping hazard or pull loos

16 July 2005 IPD4-A2-GZ40-10Fan ModuleThe 4000E fan module is installed vertically to the right of the interface module slots. It comes pre-installed

IPD4-A2-GZ40-10 July 2005 17SpecificationsProduct Documentation OnlineComplete documentation for Paradyne products is available at www.paradyne.com. S

18 July 2005 IPD4-A2-GZ40-10Important Safety Instructions1. Read and follow all warning notices and instructions marked on the product or included in

IPD4-A2-GZ40-10 July 2005 19— Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.— Never touch

2 July 2005 IPD4-A2-GZ40-10derivatives obtained from the Software, including any copy of either. If you have executed a separate written agreement cov

20 July 2005 IPD4-A2-GZ40-10CANADA – EMI NOTICE:!This Class A digital apparatus meets all requirements of the Canadian interference-causing equipment

IPD4-A2-GZ40-10 July 2005 39. Upon such termination, the Licensee shall refrain from any further use of the Software and destroy the original and all

4 July 2005 IPD4-A2-GZ40-10 2 – Rack Mount Brackets (either 19" or 23", as ordered) 10 – #6 Phillips Bracket Screws 8 – #10 Phillips Rack

IPD4-A2-GZ40-10 July 2005 5Installation in a RackUsing a Phillips Screwdriver, attach the two [2] provided rack mount brackets to the sides of the 400

6 July 2005 IPD4-A2-GZ40-10Installing Your Management ModuleA management module provides the functional control for the 4000E BLC; the 4000E cannot fu

IPD4-A2-GZ40-10 July 2005 73. Slide the Management Module Firmly into the Chassis. Tighten the fastening screws on the management module faceplate. In

8 July 2005 IPD4-A2-GZ40-10Procedure1. Select a Slot for Installation.Although the 4000E is factory shipped with Slot 1 open, interface modules may be

IPD4-A2-GZ40-10 July 2005 9Powering Up Your 4000E BLCCAUTION:Turn your DC power source(s) OFF until you have completed connection of the 4000E as outl